diff options
Diffstat (limited to 'board.h')
| -rw-r--r-- | board.h | 192 |
1 files changed, 96 insertions, 96 deletions
@@ -1,96 +1,96 @@ -#ifndef BOARD_H
-#define BOARD_H
-
-#define STM32_HSECLK 8000000
-
-#define STM32F10X_MD
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- * 0 - Analog input.
- * 1 - Push Pull output 10MHz.
- * 2 - Push Pull output 2MHz.
- * 3 - Push Pull output 50MHz.
- * 4 - Digital input.
- * 5 - Open Drain output 10MHz.
- * 6 - Open Drain output 2MHz.
- * 7 - Open Drain output 50MHz.
- * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
- * 9 - Alternate Push Pull output 10MHz.
- * A - Alternate Push Pull output 2MHz.
- * B - Alternate Push Pull output 50MHz.
- * C - Reserved.
- * D - Alternate Open Drain output 10MHz.
- * E - Alternate Open Drain output 2MHz.
- * F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input with pull-up except:
- * PA0 - Normal input (BUTTON).
- * PA2 - Alternate output (USART2 TX).
- * PA3 - Normal input (USART2 RX).
- */
-#define VAL_GPIOACRL 0x88384B88 /* PA7...PA0 */
-#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */
-#define VAL_GPIOAODR 0xFFFFFFFF
-
-/*
- * Port B setup.
- * Everything input with pull-up except:
- * PB13 - Alternate output (MMC SPI2 SCK).
- * PB14 - Normal input (MMC SPI2 MISO).
- * PB15 - Alternate output (MMC SPI2 MOSI).
- */
-#define VAL_GPIOBCRL 0x84888888 /* PB7...PB0 */
-#define VAL_GPIOBCRH 0xB4B84488 /* PB15...PB8 */
-#define VAL_GPIOBODR 0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input with pull-up except:
- * PC4 - Normal input because there is an external resistor.
- * PC6 - Normal input because there is an external resistor.
- * PC7 - Normal input because there is an external resistor.
- * PC10 - Push Pull output (CAN CNTRL).
- * PC11 - Push Pull output (USB DISC).
- * PC12 - Push Pull output (LED).
- */
-#define VAL_GPIOCCRL 0x44008888 /* PC7...PC0 */
-#define VAL_GPIOCCRH 0x88833388 /* PC15...PC8 */
-#define VAL_GPIOCODR 0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0 - Normal input (XTAL).
- * PD1 - Normal input (XTAL).
- */
-#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
-#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
-#define VAL_GPIODODR 0xFFFFFFFF
-
-/*
- * Port E setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
-#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
-#define VAL_GPIOEODR 0xFFFFFFFF
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
- void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif
-
-#endif
+#ifndef BOARD_H +#define BOARD_H + +#define STM32_HSECLK 8000000 + +#define STM32F10X_MD + +/* + * I/O ports initial setup, this configuration is established soon after reset + * in the initialization code. + * + * The digits have the following meaning: + * 0 - Analog input. + * 1 - Push Pull output 10MHz. + * 2 - Push Pull output 2MHz. + * 3 - Push Pull output 50MHz. + * 4 - Digital input. + * 5 - Open Drain output 10MHz. + * 6 - Open Drain output 2MHz. + * 7 - Open Drain output 50MHz. + * 8 - Digital input with PullUp or PullDown resistor depending on ODR. + * 9 - Alternate Push Pull output 10MHz. + * A - Alternate Push Pull output 2MHz. + * B - Alternate Push Pull output 50MHz. + * C - Reserved. + * D - Alternate Open Drain output 10MHz. + * E - Alternate Open Drain output 2MHz. + * F - Alternate Open Drain output 50MHz. + * Please refer to the STM32 Reference Manual for details. + */ + +/* + * Port A setup. + * Everything input with pull-up except: + * PA0 - Normal input (BUTTON). + * PA2 - Alternate output (USART2 TX). + * PA3 - Normal input (USART2 RX). + */ +#define VAL_GPIOACRL 0x88384B88 /* PA7...PA0 */ +#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ +#define VAL_GPIOAODR 0xFFFFFFFF + +/* + * Port B setup. + * Everything input with pull-up except: + * PB13 - Alternate output (MMC SPI2 SCK). + * PB14 - Normal input (MMC SPI2 MISO). + * PB15 - Alternate output (MMC SPI2 MOSI). + */ +#define VAL_GPIOBCRL 0x84888888 /* PB7...PB0 */ +#define VAL_GPIOBCRH 0xB4B84488 /* PB15...PB8 */ +#define VAL_GPIOBODR 0xFFFFFFFF + +/* + * Port C setup. + * Everything input with pull-up except: + * PC4 - Normal input because there is an external resistor. + * PC6 - Normal input because there is an external resistor. + * PC7 - Normal input because there is an external resistor. + * PC10 - Push Pull output (CAN CNTRL). + * PC11 - Push Pull output (USB DISC). + * PC12 - Push Pull output (LED). + */ +#define VAL_GPIOCCRL 0x44008888 /* PC7...PC0 */ +#define VAL_GPIOCCRH 0x88833388 /* PC15...PC8 */ +#define VAL_GPIOCODR 0xFFFFFFFF + +/* + * Port D setup. + * Everything input with pull-up except: + * PD0 - Normal input (XTAL). + * PD1 - Normal input (XTAL). + */ +#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ +#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ +#define VAL_GPIODODR 0xFFFFFFFF + +/* + * Port E setup. + * Everything input with pull-up except: + */ +#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ +#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ +#define VAL_GPIOEODR 0xFFFFFFFF + +#if !defined(_FROM_ASM_) +#ifdef __cplusplus +extern "C" { +#endif + void boardInit(void); +#ifdef __cplusplus +} +#endif +#endif + +#endif |