summaryrefslogtreecommitdiff
path: root/board.h
blob: 8265944f4e6009585cdb9e66555974f605bf3b07 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
#ifndef BOARD_H
#define BOARD_H

#define STM32_HSECLK            8000000

#define STM32F10X_MD

/*
 * I/O ports initial setup, this configuration is established soon after reset
 * in the initialization code.
 *
 * The digits have the following meaning:
 *   0 - Analog input.
 *   1 - Push Pull output 10MHz.
 *   2 - Push Pull output 2MHz.
 *   3 - Push Pull output 50MHz.
 *   4 - Digital input.
 *   5 - Open Drain output 10MHz.
 *   6 - Open Drain output 2MHz.
 *   7 - Open Drain output 50MHz.
 *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
 *   9 - Alternate Push Pull output 10MHz.
 *   A - Alternate Push Pull output 2MHz.
 *   B - Alternate Push Pull output 50MHz.
 *   C - Reserved.
 *   D - Alternate Open Drain output 10MHz.
 *   E - Alternate Open Drain output 2MHz.
 *   F - Alternate Open Drain output 50MHz.
 * Please refer to the STM32 Reference Manual for details.
 */

/*
 * Port A setup.
 * Everything input with pull-up except:
 * PA0  - Normal input      (BUTTON).
 * PA2  - Alternate output  (USART2 TX).
 * PA3  - Normal input      (USART2 RX).
 */
#define VAL_GPIOACRL            0x88384B88      /*  PA7...PA0 */
#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */
#define VAL_GPIOAODR            0xFFFFFFFF

/*
 * Port B setup.
 * Everything input with pull-up except:
 * PB13 - Alternate output  (MMC SPI2 SCK).
 * PB14 - Normal input      (MMC SPI2 MISO).
 * PB15 - Alternate output  (MMC SPI2 MOSI).
 */
#define VAL_GPIOBCRL            0x84888888      /*  PB7...PB0 */
#define VAL_GPIOBCRH            0xB4B84488      /* PB15...PB8 */
#define VAL_GPIOBODR            0xFFFFFFFF

/*
 * Port C setup.
 * Everything input with pull-up except:
 * PC4  - Normal input because there is an external resistor.
 * PC6  - Normal input because there is an external resistor.
 * PC7  - Normal input because there is an external resistor.
 * PC10 - Push Pull output (CAN CNTRL).
 * PC11 - Push Pull output (USB DISC).
 * PC12 - Push Pull output (LED).
 */
#define VAL_GPIOCCRL            0x44008888      /*  PC7...PC0 */
#define VAL_GPIOCCRH            0x88833388      /* PC15...PC8 */
#define VAL_GPIOCODR            0xFFFFFFFF

/*
 * Port D setup.
 * Everything input with pull-up except:
 * PD0  - Normal input (XTAL).
 * PD1  - Normal input (XTAL).
 */
#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
#define VAL_GPIODODR            0xFFFFFFFF

/*
 * Port E setup.
 * Everything input with pull-up except:
 */
#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
#define VAL_GPIOEODR            0xFFFFFFFF

#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
  void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif

#endif